HITACHI 24HB4T65 (10114594) Шасси (Main Board): 17MB110P-1K421226G212122153P6

# <- this is for comment / total file size must be less than 4KB
# console ok

#For pure PM.bin upgrade, use below part
fatload usb 0:1 0x24000000 mb110_PM51.bin
spi_wrc 0x24000000 0x00000000 $(filesize)

#For pure RomBoot.bin (include mboot.bin) upgrade, use below part
fatload usb 0:1 0x24000000 mb110_RomBoot.bin;
ncishash 0x24000000 0x24010000 0x24020000 0x24030000 0x3800 0x24033800 $(filesize)

### check file exist or not
fatpartload usb 0:1 0x21000000 mb110_en.bin 0x0 0x500000

nand erase.chip
saveenv

#--------------------------------------------------------------------
#set partition
dynpart edb64M-nand:0xA00000(KL),0x2800000(CONF),0xC700000(UBIA),0xF000000(UBIB),0x900000(tee),-(NA)
saveenv

ubi part UBIA
ubi create RFS 0x1E00000
ubi create VEN 0x9C00000

#---------------------------------------------------------------------
### direct write linux kernel image

fatpartload usb 0:1 0x21000000 mb110_en.bin 0x0 0x500000
aesdec 0x21000000 0x500000

nand erase.part KL
nand write.e 0x21000010 KL 0x500000

#setenv bootcmd nand read.e 0x205FFFC0 KL $(filesize)\; bootm 0x205FFFC0
saveenv

#---------------------------------------------------------------------
#ROOTFS
fatpartload usb 0:1 0x21000000 mb110_en.bin 0x500000 0x1E00000
aesdec 0x21000000 0x1E00000
ubi write 0x21000010 RFS 0x1E00000

fatpartload usb 0:1 0x21000000 mb110_en.bin 0x2300000 0x9C00000
aesdec 0x21000000 0x9C00000
ubi write 0x21000010 VEN 0x9C00000

ubi part CONF
ubi create CON 0x1E00000
fatpartload usb 0:1 0x21000000 mb110_en.bin 0xBF00000 0x1E00000
aesdec 0x21000000 0x1E00000
ubi write 0x21000010 CON 0x1E00000

ubi part UBIB
ubi create BUF 0xBF00000
ubi create APD 0x1E00000

fatpartload usb 0:1 0x21000000 mb110_en.bin 0xDD00000 0x1100000
aesdec 0x21000000 0x1100000
ubi write 0x21000010 APD 0x1100000

#---------------------------------------------------------------------
#TEE
fatpartload usb 0:1 0x21000000 mb110_en.bin 0xEE00000 0x502210
aesdec 0x21000000 0x502210

nand erase.part tee
nand write.e 0x21000010 tee 0x500000

store_secure_info kernelSign 0x21501010
store_secure_info teeSign 0x21501230

setenv LOAD_NUTTX nand read.e 0x50000000 tee 0x600000\;
setenv BOOT_NUTTX bootNuttx 0x10000000\;

store_nuttx_config NuttxConfig 0x21500010

#---------------------------------------------------------------------
#Force Mboot to update environment after update
setenv sync_environment 1
saveenv

printenv
reset

% <- this is end of file symbol